Claims (1)
Устройство для микроинвазивной микрофрагментарной высокоскоростной витрэктомии, содержащее наружную трубку, закрытую с торца, снабженную боковым аспирационно-резекционным окном и неподвижно закрепленную к рукоятке, и внутренний подвижный нож, соединенный с приводом управляемым педальным пультом аппарата и выполненный с возможностью, как единичных, так и множественных перемещений и трех положений ножа по отношению к аспирационно-резекционному окну - полного открывания окна для выполнения аспирации, частичного перекрывания окна для захвата и удержания ткани, и полного перекрывания окна для разрезания захваченной ткани, отличающееся тем, что наружная трубка соединена посредством рукоятки со шлангом системы аспирации аппарата и выполняет функцию аспиратора, диаметры наружной трубки составляют - наружные от 0,3 до 0,5 мм и внутренние соответственно от 0,2 до 0,35 мм, ее дистальный торец перпендикулярно срезан и закрыт пробкой, выполненной из электроизоляционного материала и напрессованной и/или наклеенной после формирования торца, боковое аспирационно-резекционное окно наружной трубки вырезано электроэрозионным методом в виде квадрата или продольного или поперечного прямоугольника высотой от 0,3 до 0,5 мм соответственно диаметру наружной трубки и шириной от 1/3 до 2/3 ее периметра, и расположено от торца не выше 150 мкм, а нож изготовлен из высокопрочного стального или твердосплавного монолитного стержня, который выполнен круглым в пределах рукоятки и основания наружной трубки, а к режущему концу сформирован продольно и поперечно сложно усеченным, вставлен без или с минимальным зазором в наружную трубку и рукоятку с возможностью продольных возвратно-поступательных или ротационных перемещений, выходит за пределы рукоятки и разъемно соединяется с валиком привода, который прикреплен к рукоятке с возможностью угловых перемещений хирургом во время проведения операции в положения от 0 до 90 градусов к продольной оси ножа, при этом в положении привода от 0 до 45 градусов нож выполняет ротационные право- или левосторонние движения, а от 45 до 90 градусов - нож движется продольно возвратно-поступательно, при этом в качестве привода ножа используют коллекторные или бесколлекторные микроэлектродвигатели или серводвигатели снабженные контроллерами перемещений валика, обеспечивающими контролируемое дозированное движение ножа в заданном направлении со скоростью вращения и продольных перемещений от одного до ста тысяч в минуту, и полное открывание/закрывания или частичное перекрывание ножом аспирационно-резекционного окна как с зазором от 5 мкм до 300 мкм, так и на 1/3, 2/3, 3/4 высоты или ширины окна, кроме того, наконечник витреотома и электропривод подключены к системе аппарата, поглощающей электромагнитный потенциал, возникающий при работе витреотома.
A device for microinvasive microfragmented high-speed vitrectomy, comprising an outer tube closed from the end, equipped with a lateral aspiration-resection window and fixedly attached to the handle, and an internal movable knife connected to the drive by a controlled pedal console of the device and made with the possibility of both single and multiple movements and three positions of the knife in relation to the aspiration-resection window - full opening of the window to perform aspiration, partial overlapping of the window for grasping and holding tissue, and completely overlapping the window for cutting the captured tissue, characterized in that the outer tube is connected by a handle to the hose of the aspiration system of the apparatus and acts as an aspirator, the diameters of the outer tube are external from 0.3 to 0.5 mm and internal respectively, from 0.2 to 0.35 mm, its distal end face is perpendicularly cut off and closed with a stopper made of electrical insulating material and pressed and / or glued after the formation of the end face, the side aspiration-resection window on the outer tube is cut by an electroerosion method in the form of a square or a longitudinal or transverse rectangle with a height of 0.3 to 0.5 mm, respectively, the diameter of the outer tube and a width of 1/3 to 2/3 of its perimeter, and is located from the end not higher than 150 microns, and the knife is made of a high-strength steel or carbide monolithic rod, which is made round within the handle and base of the outer tube, and is formed longitudinally and transversely difficultly truncated to the cutting end, inserted without or with a minimum clearance into the outer tube and arm tissue with the possibility of longitudinal reciprocating or rotational movements, extends beyond the handle and detachably connects to the drive roller, which is attached to the handle with the possibility of angular movements by the surgeon during the operation in the position from 0 to 90 degrees to the longitudinal axis of the knife, while the position of the drive from 0 to 45 degrees, the knife performs rotational right- or left-handed movements, and from 45 to 90 degrees - the knife moves longitudinally reciprocating, while collectively use the knife drive ni or brushless micro electric motors or servomotors equipped with roller movement controllers providing controlled dosed movement of the knife in a given direction with a rotation speed and longitudinal movements of one to one hundred thousand per minute, and full opening / closing or partial overlapping of the aspiration-resection window with a knife as with a gap from 5 microns up to 300 microns, and at 1/3, 2/3, 3/4 of the height or width of the window, in addition, the vitreotome tip and the electric drive are connected to the system of the device absorbing electric the electromagnetic potential arising from the operation of the vitreotome.