Claim Missing Document
Check
Articles

Found 40 Documents
Search

FLOW-INDUCED TRANSVERSE VIBRATION CHARACTERISTICS OF CANTILEVERED RECTANGULAR AND D-SECTION STRUCTURE FOR ENERGY HARVESTING Kadir, Kadir; Barata, La Ode Ahmad; Kiwata, Takahiro; Fernanda, Yolli
Jurnal Fokus Elektroda : Energi Listrik, Telekomunikasi, Komputer, Elektronika dan Kendali) Vol 5, No 2 (2020): Jurnal Elektroda Vol 5 No 2
Publisher : Universitas Halu Oleo

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.33772/jfe.v5i2.12298

Abstract

We considered the effect of aspect ratio L/H (where L is span length of a prism, and H is the height of a bluff body normal to the flow direction) on the response amplitude of cantilevered rectangular and D-shaped cross-section prims for energy harvesting. The prism was mounted elastically to a plate spring attached to the ceiling wall with a jig in the test section of the water tunnel. The prism with an aspect ratio of L/H = 2.5 has a small angle amplitude as compared to that with L/H ≥ 5. Increment rate of response amplitude of prisms increased proportionally with the aspect ratio. The D-section prism with an aspect ratio of L/H = 10 has a stable peak amplitude and a large increment rate of response amplitude. Therefore, the D-section prism with L/H = 10 is a more suitable cross-section for energy harvesting from transverse-galloping vibration. By using magnetostricitve material as harvester energy, potential power gained from small side ratio for both prism that is 0.99 and 0.48 volt for D-section and rectangular prisms respectively.  Keywords—Flow-induced vibration, Cantilevered prism, Rectangular prism, D-section prism, Aspect ratio
Studi Karakteristik Biomassa Batang Pohon Gamal (Gliricidia Sepium) Barata, Laode Ahmad
Jurnal Fokus Elektroda : Energi Listrik, Telekomunikasi, Komputer, Elektronika dan Kendali) Vol 6, No 2 (2021): Jurnal Elektroda Vol 6 No 2
Publisher : Universitas Halu Oleo

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.33772/jfe.v6i2.18784

Abstract

Tujuan penelitian ini adalah untuk mengetahui karakteristik dari batang gamal melalui uji nilai kalor, proximate dan uji ultimate. Penelitian ini dilakukan dengan variasi campuran 60% arang gamal, 30% batubara, 10% perekat dan 70% arang gamal, 20% batubara, 10% perekat serta 100% arang gamal. Pada pengujian nilai kalor digunakan alat DSC, sedangkan untuk pengujian proximate dilakukan dengan metode gravimetri, yaitu pemanasan material dengan suhu tertentu. Untuk pengujian ultimate digunakan alat XRD yatu pemberian sinar X pada material sehingga unsur kimianya dapat terbaca. Hasil pengujian nilai kalor paling tinggi terdapat pada campuran 60% arang gamal, 30% batubara, 10% perekat yaitu 535,3351 J/g. Dari hasil analisis proximate diperoleh hasil layak untuk kualifikasi biomassa arang terdapat pada campuran 60% arang gamal, 30% batubara, 10% perekat dengan kandungan karbon tetap sebesar 78.7%, kadar air adalah 2,69%, vollatile mater 13,24%, kadar abu 5,37%.  Dari analisis ultimate, diperoleh hasil baik terdapat pada komposisi 100% arang gamal dengan komposisi lengkap yaitu kadar karbon 35,4%, hidrogen 23%, nitrogen 13%, sulfur 3,6%, dan oksigen 21% dengan nilai kalor atas (HHV) sebesar 349 J/gram.
STUDI KARAKTERISTIK BRIKET BIOMASSA BATANG SINGKONG Kadir Kadir; LD Ahmad Barata
Dinamika : Jurnal Ilmiah Teknik Mesin Vol 2, No 2 (2011)
Publisher : Jurusan Teknik Mesin, Universitas Halu Oleo

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.33772/djitm.v2i2.311

Abstract

Tujuan penelitian ini adalah membuat dan menguji karakteristik briket biomassa dari batang singkong (ubi kayu) sebagai sumber energi alternatif. Briket dibuat dengan ukuran partikel 20 mesh dan 80 mesh dengan jenis massa 4 gram dan 5 gram yang dicampurkan cairan pengikat (binder) sebanyak 23% kemudian dicetak dengan diameter cetakan 1,8 cm dan tekanan kompaksi 100 kgf/cm2. Briket yang telah dicetak di keringkan selama ± 4 hari yang selanjutnya dilakukan pengujian shatter index, laju perubahan temperatur dan pengurangan massa pembakaran diuji serta uji masak menggunakan tungku tradisional. Hasil uji proksimasi briket yang dihasilkan juga ditunjukkan. Hasil pengujian menunjukkan bahwa kualitas briket biomassa yang dihasilkan cukup baik, baik dari segi karakteristik pembakaran maupun ketahanan briket, briket ini dapat dijadikan bahan bakar alternatif.
Studi Bahan Isolator berbahan Dasar Limbah Batubara Bottom Ash La Ode Ahmad Barata
Dinamika : Jurnal Ilmiah Teknik Mesin Vol 7, No 2 (2016)
Publisher : Jurusan Teknik Mesin, Universitas Halu Oleo

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (732.237 KB) | DOI: 10.33772/djitm.v7i2.1047

Abstract

Tujuan penelitian ini adalah untuk mengetahui konduktivitas panas dan kuat tekan campuran limbah bottom ash, tanah liat dan gypsum untuk bahan isolator. Penelitian ini dilakukan dengan memvariasikan campuran bahan isolator dengan komposisi bottom ash, tanah liat dan gypsum. Ada dua bentuk spesimen yang dibuat dalam penelitian ini yakni bentuk plat dan bentuk silinder. Pada sampel bentuk silinder dilakukan pemanasan 160 oC selama 3 jam. Uji konduktivitas termal menggunakan metode langsung dimana spesimen plat uji diberikan fluks panas lampu halogen 150W dalam wadah tertutup, sedangkan spesimen silinder dilakukan uji kuat tekan dengan standar ASTM C165-95. Densitas spesimen juga ditentukan dengan uji prinsip Archimedes. Hasil pengujian sampel menunjukan bahwa komposisi bottom ash yang tinggi menunjukkan konduktivitas termal yang lebih rendah (isolator yang baik), sedangkan penambahan tanah liat menunjukan kuat tekan yang lebih baik.
Karakteristik Getaran Model Silinder Kantilever dan Prestasi Magnetostrictive Material sebagai Pemanen Listrik Mikro Berbasis Getaran La Ode Ahmad Barata; Takahiro Kiwata
Dinamika : Jurnal Ilmiah Teknik Mesin Vol 12, No 2 (2021)
Publisher : Jurusan Teknik Mesin, Universitas Halu Oleo

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.33772/djitm.v12i2.20385

Abstract

Penelitian pembangkit daya berbasis getaran dengan menggunakan material magnetostrictive dan getaran yang ditumbulkan oleh aliran fluida dilakukan secara ekperimental menggunakan terowongan angin. Prisma dan silinder model kantilever dengan variasi panjang digunakan sebagai menggangu aliran untuk memicu terjadinya getaran. Penelitian ini berfokus pada getaran transversal yang diinduksi oleh olakan vorteks untuk kasus silinder dan getaran yang dimunculkan karena adanya perbedaan tekanan antara dua sisi prisma yang diakibatkan oleh pemisahan aliran pada ujung depan prisma uji. Prisma yang digunakan memiliki rasio tebal D/H = 0.2 dan 1 dimana D = tebal prisma dan H adalah tinggi penampang melintang tegak lurus arah aliran. Daya listrik maksimum dihasilkan oleh model prism dengan bentang pendek karena memiliki frekuensi alami yang rendah. Namun demikian, model ini memerlukan kecepatan aliran yang tinggi untuk memulai getaran. Pengaruh penggunaan cap (penutup ujung model uji) juga dibahas dalam penelitian ini. Daya yang dibangkitkan oleh model uji silinder dengan panjang bentang 200 mm atau L/H = 5 adalah 1.8 mW yang merupakan nilai maksimum pembangkitan untuk semua model uji yang digunakan. Daya yang dihasilkan dari generator mikro ini berpotensi untuk menjadi sumber listrik bagi sensor dan perangkat nirkabel lainnya.
KAJIAN PRESTASI DAN EKONOMISITAS BRIKET BATUBARA SEBAGAI BAHAN BAKAR ALTERNATIF Yuspian Gunawan; LD Ahmad Barata
Dinamika : Jurnal Ilmiah Teknik Mesin Vol 3, No 1 (2011)
Publisher : Jurusan Teknik Mesin, Universitas Halu Oleo

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.33772/djitm.v3i1.306

Abstract

Tujuan dari penelitian ini adalah untuk mengetahui prestasi termal dan ekonomisitas dari bahan bakar briket batubara. Dengan menggunakan briket dan kompor yang telah ada di pasaran, bahan bakar briket batubara digunakan untuk memanaskan air dengan massa 10 kg, 5 kg dan 1 kg. Hal yang sama juga dilakukan pada kompor yang menggunakan miyak tanah dan elpiji. Dalam proses pemanasan ini temperatur air,nyala api diukur dengan menggunakan termokopel setiap 5 menit hingga temperatur air mencapai 100oC. Kemudian temperatur udara sekeliling juga diukur dengan termometer raksa. Setelah itu massa bahan bakar dan air yang diuapkan diukur. Berdasarkan penelitian ini, temperatur nyala briket batubara mengalami kenaikan yang relatif lambat hingga memerlukan waktu yang relatif lama untuk mendidihkan air sedangkan jika menggunakan bahan bakar elpiji  dan minyak tanah kenaikan temperaturnya relatif cepat dan mendidihkan air relatif cepat. Prestasi Termal dan keekonomian briket batubara pada pemanasan yang relatif lama (di atas 80 menit) dan atau pada beban pemanasan yang besar (di atas 5 kg air) diperoleh prestasi termal dan ekonomisitas yang lebih baik. Sedangkan pada beban pemanasan yang relatif ringan atau singkat, pemanasan dengan elpiji  dan minyak tanah diperoleh prestasi termal dan ekonomisitas yang lebih baik.
Experimental Investigation of Bladeless Power Generator from Wind-induced Vibration La Ode Ahmad Barata; Kiwata Takahiro; Toshiyuki Ueno; Samhuddin Samhuddin; La Hasanudin
International Journal of Renewable Energy Development Vol 11, No 3 (2022): August 2022
Publisher : Center of Biomass & Renewable Energy, Diponegoro University

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.14710/ijred.2022.43888

Abstract

The power harvester unit from flow-induced vibration (FIV) was designed to harness energy from low flow velocity based on the magnetostrictive effect on the galfenol (Fe – Ga alloy) strip induced by the oscillating bluff body. This study aimed to investigate the cross-section variation’s effect on the FIV characteristics and the magnetostrictive material’s performance for the bladeless power generator. The generator model’s vibration characteristics and performance tests were conducted in the wind tunnel test using the wind-receiving unit (WRU) variation. The results showed that the resonance reduced-velocity (Vr) were around 3.7 and 4.0 for rectangular and circular cylinders, respectively. Furthermore, the effect of rectangular depth variation on the power generation output is linear to the test models’ displacement rate and vibration frequency. The harvester’s maximum power generation was 5.25 mW, achieved using the rectangular prism with depth D = 0.4H. The power coefficient was also evaluated for different wind-receiving models. The harvester model lit up 54 LED lamps in the wind tunnel test. The voltage output is sufficient to provide electric power resources for an IoT system, sensor, and wearable or wireless devices. The harvester model successfully generated a voltage signal under the initial field test with an ambient wind velocity of 0.9 – 2.71 m/s. Therefore, this study recommends the development of bladeless power generators in the future.
KARAKTERISTIK PEMANEN DAYA LISTRIK BERBASIS GETARAN STRUKTUR La Ode Ahmad Barata; Samhuddin Samhuddin
Jurnal Rekayasa Mesin Vol. 13 No. 3 (2022)
Publisher : Jurusan Teknik Mesin, Fakultas Teknik, Universitas Brawijaya

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.21776/jrm.v13i3.1268

Abstract

Mechanical vibration is a potential source of micro-electrical energy harvesting mechanisms for micro electrical power supply for IoT system networks, wireless and sensors where the power requirements are relatively lower and available independently. In this study, the characteristics of the cylinder vibration response as a trigger for energy harvesting from flow-induced vibrations at various air velocities were investigated experimentally in a wind tunnel test section. Harvesting of micro power from cylinder’s motion by using galfenol (Fe-Ga) material was also investigated simultaneously. The maximum cylinder’s vibration response was obtained by using the plain cylinder model. Cylinder taper variation reduce the maximum vibration response. The position of the major (D) and minor (d) (or inverse position) diameters also affects the vibration response. However, tapering the cylinder reduces the onset vibration with respect to the flow velocity. The frequency of the vortex (Strouhal, St) ranges from 0.25 to 0.12. The minor diameter of the tapered cylinder has the effect on decreasing the vibration response and tends to be stationary. Minor diameter reduction reduces the potential for vibration to the structure. The maximum power generated by the test model is about 8.5 mW with the power RMS value of 2.3 mW and power coefficient about 4%.
Pelatihan Teknik Pengecoran Aluminium Bagi Usaha Pengepul Barang Bekas Di Kecamatan Poasia Kota Kendari Sudarsono Sudarsono; Aminur Aminur; Budiman Sudia; Nanang Endriatno; La Ode Ahmad Barata
Jurnal Pengabdian Masyarakat Ilmu Terapan Vol 4, No 2 (2022)
Publisher : Vokasi Universitas Halu Oleo

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.33772/jpmit.v4i2.28245

Abstract

Handling of used aluminum has been carried out by collectors, namely the compression process. The pressing process is less economical because it still produces cavities and the selling price is low. The purpose of this community service activity is to provide training on Aluminum smelting with casting techniques for two groups of independent collectors, Mandiri Berkah and Maju Jaya. The activity took place in the Mandiri Berkah collector area which was attended by Mandiri Berkah and Maju Jaya employees and the community around Poasia. The method of implementing the activity is a theoretical explanation of Aluminum and its processing method with casting techniques. Used aluminum cans are melted in a charcoal-fired crucible furnace. The used aluminum cans are put in the kowi which is placed in a hot furnace. After the cans are melted, they are poured into rectangular molds. The results of the service activities that resulted were the opening of knowledge insights related to used aluminum. Participants were able to recycle Aluminum by casting technique into ingot products.Keywords: Training, foundry, aluminum, collectors
analisa keselamatan dan kesehatan kerja pada pengoperasian forklift di Pt. equiport inti indonesia Harjum La Bau; Muh Fadhil Safli; Sudarsono; La Ode Ahmad Barata
Piston: Jurnal Teknologi Vol 7 No 2 (2022): Desember 2022
Publisher : Program Pendidikan Vokasi Teknik Mesin

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (564.188 KB) | DOI: 10.55679/pistonjt.v7i2.7

Abstract

Occupational Health and Safety (K3) is our effort to create a healthy and safe work environment so as to reduce the probability of occupational accidents and diseases due to negligence which results in demotivation and deficiency in work productivity. At PT. Equiport Inti Indonesia, the application of forklift operating safety regulations has not been carried out thoroughly. The non-implementation of the implementation of the regulations as a whole can trigger work accidents. The purpose of this final project is to find out the steps taken by the company in preventing work accidents in forklift operations. The method used in this final project uses interviews and direct observation in the company to fill in the checklist table that has been prepared as a data collection tool. The analysis in this final project uses a fishbone diagram. The use of fishbone diagrams is carried out to trace the causes and effects that arise from the deficiencies found that can lead to forklift work accidents. The results of this final project show that PT. Equiport Inti Indonesia still lacks in implementing safety standards in forklift operations, including the absence of pedestrian paths, incomplete forklift safety signs, and the operator's lack of seriousness in operating forklifts. From the results of this final project, it can be concluded that the company pays little attention to the procedures for implementing occupational safety and health in forklift operations.