Mike had been asked by the Chief of U.S. Information Agency, the parent of Voice of America, if there might be some way to counter Soviet jamming of VOA broadcasts. His mind set to work: he made a pile of different antennas that seemed to show some promise, and presented a proposal to USIA to produce two different anti-jam antennas that would be effective. I was at VOA engineering. His proposal became a contract: by the best of luck, engineering thrust me into the role of "ARCO" - authorized rep of the contracting officer (all other government agencies call this "COTR," but USIA is, well, different!)
Mike showed me myriad designs that filled his pool house to the max! We selected two promising ones, and spent the rest of the year studying them, improving them, and producing a really neat end product. One counters jamming via sky wave, where the jammer propagates by ordinary HF propagation. The other counters ground wave jammers - noise transmitters located near the receiver, usually on the outskirts of the city being jammed.
Ground wave jamming is exactly similar to arcing power lines or other locally produced noise from appliances and the like - even from lightning.
So, without further delay, I present, in picture form, . . .
Get a 2' x 2' base - plywood, cardboard, stiff foam plastic, even the back of a wall-hung picture.
Put the insulating sheet over the first part of the foil and tape it in place, per the drawing.
Put the receiver on the foil as shown. Don't worry about electrical connection: the capacity between the receiver and the foil will do the trick nicely.
Pull the whip antenna out, and lay it on the other side of the foil loop. Use a small weight to make sure the whip contacts the foil.
To tune the antenna, set the receiver about the middle of the desired band, with the volume control fairly high. Tune for strongest signal, or strong increase in noise from the receiver.
The pickup loop can be brought to the receiver by twisted pair or by RG-58 or similar coaxial cable.
THIS ANTENNA IS NOT DESIGNED FOR TRANSMITTING!!
While listening to the interfering noise, tip the antenna a bit to reduce the noise. Many times, with just a minute or so of adjusting, the noise from power lines, nearby TV sets, etc. can be reduced 20 dB, and further noise canceling can be obtained with a bit more care.
The newspaper and two foil flaps make a capacitor. The book allows you to vary the amount of overlap of foil, so you made a variable capacitor which is attached to the ends of a single turn loop, made of a very wide, flat conductor.
The receiver, sitting on the foil, has a good deal of capacity between its internal circuit board (or chassis) to one end of the loop. Its whip antenna is connected to the other end, so the voltage developed across the loop is injected into the receiver.
Tuning the loop causes the voltage at one frequency to be maximized. This causes the increase in signal strength.
Mike's HLA is horizontally polarized. Therefore it doesn't respond to the noise. But skywave signals arrive at your receiver randomly polarized, so their horizontal part enters the antenna. As their polarization varies, though, the signal will "fade." But this happens with any shortwave receiving antenna. So Mike's HLA suffers from fading no more than any other. It's forte is noise cancellation.
If you decide to make a bigger HLA, just keep in mind that the total circumference of the outside edge of conductor should be kept to well under one-third wavelength. Otherwise, the result will no longer be a small, horizontal loop above ground, but will have other (maybe even interesting) properties.
We've made HLA's from material other than aluminum foil. Sheet aluminum, sheet steel, window screen wire (but not fiberglass, which was the reason for my first failure to get one to work!) or lots of other conducting material will work fine. When using strips of metal, Cheryl discovered you don't need to electrically bond the pieces together. She just put weights at the corners, and the capacity through the oxide layers was essentially a very good connection at RF frequencies.
The HLA was designed to cancel vertically polarized noise. To do so, it was engineered to be kept within about a tenth of a wavelength above ground - not elevated much at all. You can, of course, put them up much higher, but I offer no data on performance when the loop is elevated - other people can attest to the qualities of elevated, horizontal loop antennas.
I hope you find this antenna interesting and useful. Some time ago, I had built one and was using it for reception on 15 meters, while using a grasswire for transmitting. In contact with a ham in Europe, I noticed the lights blinking on and off slightly. When I quit with the QSO, I went upstairs to ask my XYL what the heck she was doing - only to find myself in the middle of a raging thunderstorm! The grasswire, being rather impervious to lightning, and the HLA cancelling QRN from the lightning, kept me from realizing that a storm was even in progress!
For more unusual antennas, visit my web page.
And check out my Books
K3MT